ANIMAL REPELLER USER MANUAL 

Thank you for choosing Pest Destruct Animal Repeller!

Please read and understand these instructions and keep this manual for future references 

HOW IT WORKS

Pest Destruct Animal Repeller is designed for permanent service, allowing you to install it once and let it work! It is weather-proof and resistant to all weather conditions, which is why it is suitable for outdoor use. 

It uses a solar panel, located on the top of the unit to recharge the internal batteries. The passive infrared sensor- PIR, detects motion and triggers the ultrasonic speaker, which then starts emitting a high-frequency sound that humans cannot hear, but it bothers animals’ hearing and nervous system, making them feel uncomfortable and causing them to leave your space. It chases away common outdoor pests like deer, raccoon, mice, skunks, squirrels, chipmunks, possums, woodpeckers, bats, beetles, earwigs, snakes, armadillos, cats and dogs, and more.

This solar animal repeller is a safe and humane way to keep unwanted animals away.

WHAT’S IN THE BOX? 

1. 3 parts of the spike

2. Solar panel head device

3. Instructions

***Note: spikes come disassembled and securely packed in the bottom part of the box, under the cardboard, which might make them hard to notice. Always make sure you have fully unpacked the product before you start the setup. 

SETUP

1. Please read the manual before you start using the product

2. Unpack the product completely and confirm that all parts are included

3. Connect the repeller’s head, spike extensions, and ground stake

4. On the upper part of the device, you will notice a protective film. The removal of the protective film is optional, its purpose is only to protect the solar panel from scratch, and you can either remove it or leave it on. 

5. Install the unit in a place where it can catch most of the sunlight during the day, and put it pointed towards the place you wish to protect. 

6. Insert the spike into the ground carefully. Please leave the spike 5 inches or more above the ground. It is suggested that you dig a hole and then insert the unit to ensure no damage occurs.

7. Place the unit in direct sunlight and “OFF” position for 24 hours prior to first use to ensure the product is fully charged. You may repeat this action every time you start using the product again after a long resting time (such as, after winter), or if you had many consecutive cloudy days, which caused the battery to get low. 

8. Once turned ON, the Red-LED light and ultrasonic signal will activate for about 100 seconds. Following this activation, the unit will move to Stand-by mode.

OPERATION AND INSTALLATION 

Please install the device facing the direction that animals and pests will come from to have a better effect. The device will activate each time an animal appears within its range. The red light will turn on when motion is detected, indicating that the high-frequency sound is being emitted.  When there is no motion, the unit will go back to standby mode. The red light can be long or short blinking light, and the small ticking sound might appear.

The device is designed to be used outdoors, installing the product in an outdoor area, without many objects directly in front of it as it may diminish the range of the electromagnetic waves.

For flying pests, such as bats, woodpeckers, or animals that normally rest in the trees, place the unit on higher altitudes so that animals can be under direct impact of the ultrasonic waves. The top of the device has a hole for hanging, so the item can also be mounted on a wall, pillar, or balcony as an alternative to mounting in the ground.

TECHNICAL SPECIFICATIONS 

Infrared sensor angle: 110° horizontally, 50° vertically 

Detection range: 26-30 feet 

Power supply: 4 x 2/3AA Nickel hydride rechargeable batteries, included and integrated with the device

Charging time: approximately 6 hours 

Frequency: 25-61kHz

Product dimensions: Stake: 12.6",  “head”: 5.6"x3.75"

Color: Green

BATTERY 

The product uses 4 x 2/3AA Nickel hydride rechargeable batteries, included and integrated with the device. The batteries should not be taken out and recharged at your home, they recharge themselves with solar energy, make sure to put the product in a place where it can catch most of the sunshine during the day to enable fast and sufficient recharge.

If the rechargeable batteries in the product have not been in use for an extended period, place the unit in direct sunlight and “OFF” position for 24 hours so that the battery can fully recharge and revive. 

If you are replacing the batteries, please dispose of the old batteries properly at a recycling center for used electrical and electronic devices.

MAINTENANCE AND CLEANING 

To clean the device, use a soft cloth dampened with mild soap and water. Do not use harsh chemicals or abrasive cleaning products that may damage the device.

IMPORTANT NOTICES

*** Do not cover up the PIR sensor or solar panel of the device 

*** The device works on the principle of motion detection, make sure the device is not nearby the road, or place with a lot of activities as it would constantly get triggered, which might diminish the battery life 

***The noise frequency of this unit is above the normal human range of hearing (20Hz – 20kHz), however, some people may still be able to hear the lower range of the ultrasound the unit emits (~25kHz). For this reason, please place the unit out of earshot of common areas

*** Please keep away from children and only operate after thoroughly reading the instructions

***Do not throw away the box or any part you have received with the product, as you might need them in case you decide to return the product 

Ultrasonic Pest Repeller 

How it works:

The electronic Pest Destruct pest repeller adopts modern microelectronic technology to produce automatically changing ultrasound intermittently and alternately. Then, through a unique ultrasonic speaker, it emits ultrasonic waves which make the hearing and nervous systems of pests uncomfortable. Once the device is plugged in, the pests will move away from the area/range the ultrasonic waves are reaching.

Product Specifications

1. Voltage: 100-240V AC, 50/60HZ
2. Power: 2.5w
3. Output Audio: 20-65KHz

Useful info:

1. Pest Destruct pest repeller is able to drive away Ants, Mice, Rats, Roaches, Cockroaches, Bats, Squirrels, Flies, Fruit Flies, Silverfish, Mosquitoes, Spiders, Bed Bugs, Stink Bugs, Crickets, Fleas, Bugs, Moths, Termites, Wasps, Beetles and many other annoying pests! Humans and family pets will not be harmed by the ultrasonic sound emitted from the device.
2. The device will work best in a room measuring 100 to 800 square feet.
3. Pest Destruct pest repeller is widely used in homes, stores, hospitals, offices, and even in hotels!
4. Avoid installing the pest repeller in a carpeted area or near curtains and other sound-absorbing materials that could reduce the effectiveness of the device. During the first few days of use, it is not uncommon to see a significant increase in pests as they are vacating a nearby nest. The ultrasonic sound will drive pests out of nests that you even may have been completely unaware of.

Installation: 

1. Unpack the product and plug-in. Aim the product's speaker directly at the pest area.

2. There should be no obstacles or hard objects [ No walls, ceiling, furniture...] in front of the device.

Precautions

1. Do not put this product outdoors or in a hot or humid environment. Do not allow this product to come into contact with water or other liquids.

2. Be sure to inform children in advance: Do not play with this product while it is working.

3. To avoid electric shock, accidents, and safety hazards, non-professionals are prohibited from opening this product to repair it.
   
   

FREQUENT QUESTIONS: 

1. Is it safe for my dog, cat, or pet? 

Yes, the device is designed to be completely safe for pets! 

2. Where do I need to put it?

The product should be plugged in as close as possible to the infested area. 

3. How many do I need for my home?

One unit covers 100-800 sq ft of indoor space, hence the number of units that would be suitable for you will mostly depend on the size of the area you wish to treat. The ultrasound cannot penetrate hard obstacles or walls, ceilings, floors, which also might be an important factor to consider when deciding on how many units you need. 

4. Can it be used outdoor?

The product is not designed to be used outdoors. It is an electrically powered plug-in, if placed outdoors it will be exposed to various weather conditions that might cause failure (flood, rain, snow...)

5. Is it battery operated? 

The device is not battery-operated, it is a plug-in electrically powered device. 

6. What is the area coverage of one unit? 

One unit covers 100-800 sq ft. 

7. For how long will this product last? 

The product can last really long if stored accordingly, even a year or two, but it is something that will depend on how the units are maintained. After the pests are gone, it is advised to plug out the product and keep it in a dry and cool space for later use. 

8. Will this device be bothered by my other appliances? 

The device will not be affected by other devices and vice versa. 

9. I can hear the sound that the device emits. Is it normal? 

The device is designed to be completely silent to the human ear. In case your unit emits perceptible sound, please contact our team for a replacement. 

10. Is the light suppose to blink or stay steady? 

This will depend on the model of the product you’ve purchased. Some units will have a blinking light, while others will have a steady light. Please check the manual or contact our team to confirm the information.

EXLPON Dash Camera 

Vehicle Black Box DVR 

Full HD with 3" LCD Screen

INTRODUCTION

• Thank you for purchasing our Explon Dash Camera- Full HD 3" LCD Screen vehicle black box

• This user manual will contain complete instructions on how to operate your Dash Cam and is highly recommended to read it prior to use

• This product is intended for use in motor vehicles solely. When mounting the product, ensure the device is not installed where it might interfere with the driver's field of vision or disturb the deployment of the airbag 

•  The product requires a memory card to operate (not included in the package), the suggested type is a high-speed class 10, 32GB max micro SDHC card

• Do not leave the product in direct sunlight for a long time or if the temperature goes above 170°F (75°C)

BOX INCLUDES

*The content of the package may vary 

INSTALLATION GUIDE

• Before installation, please insert the Memory card in the slot, taking care that the gold contacts are facing towards the LCD screen side of the Dash Cam. Push the memory card until it clicks into place. Format the memory card prior to use. Do not remove or insert the memory card when the Dash Cam is turned on. This may damage the memory card or recordings within.

• Connect the power adapter to the 12V cigarette lighter socket and route the cable in the interior/ hide the excess cable into the interior panel and gaps to obtain visual aesthetics

• If the device is properly installed, the red light will appear at the top left corner and indicates charging

• The device contains a battery whose purpose is to backup and save the data only. In order to make the device work, it has to be plugged in the cigarette lighter and the car has to be in the ignition, or the Dashcam must be connected to your PC with the USB cable 

• After the installation is completed, please turn the unit ON by pressing the Power button located on the left side of the Dash Cam and start the engine

KEY BUTTONS

1.    TF Memory Card Slot: Insert/Remove the memory card when the camera is off to avoid data loss

2. UP- use this button to navigate the menu 

3. MENU- Press this button to open the SETTINGS menu. Press twice to get to another page of the SETTINGS menu

4. DOWN- use this button to navigate the menu 

5. HDMI- this port is used to connect this device to a TV/PC with an HDMI cable (cable not included in the package)

6. USB PORT- this port is used to attach this device to a car charger or to connect the device to the PC with a USB cable  

7. RESET- in case your Dashcam crashes, it is recommended to take a paper clip or similar to reset the camera

8. MIC- internal component, not recommended to tackle this port 

9. OK- Use this button to select or enter features, or confirm changes you made within options 

10. MODE- This button is used to switch between camera Video/Photo/Playback 

11. LOCK- Once the recording is started, this button shall be pressed to save the current video or photo 

12. POWER- Long press this button to turn the device ON or OFF. The short press will only turn on the Screen saver and the device will keep recording, even though the screen is dark 

FUNCTIONS DESCRIPTION AND START-UP

1. Once the device is turned ON, the device will automatically be in the recording mode. If the device is connected to the PC with the USB cable, the user will be able to see three different selections: 

1.Mass storage

2.PC camera

3.REC_mode

To enter Camera mode, use the UP/DOWN buttons on the left, select REC_mode, and click OK on the right side of the Dashcam.

FORMATTING THE MEMORY CARD 

Please note that the micro SD Card is not included in the package. The suitable micro SD Card for our device is a high-speed class 10, 32GB max micro SDHC card.

Once the micro SD card is inserted, please press the Power button to turn on the device.  Double click the Menu button (it’s located on the left, right between the UP and DOWN buttons), and use DOWN to scroll down to the Format option. Click OK. 

You will see on the screen:

“Format

Delete all data” will have two selections: 

1. Cancel 

2.  OK 

Select the “OK” option and press the “OK” button. Your memory card is now formatted and contains no data. 

RECORDING 

Once the device is turned on and the memory card is formatted, you will enter Video mode. 

Press the “OK” button to start/stop recording.

Once the recording is started, the red indicator will be flashing next to this icon   in the top left corner of the screen. 

If the recording is stopped, there will be no red flashing indicator. 

By pressing the LOCK button (third button on the right       ), you will manually lock the current video file. The Loop recording will not override the locked recording, it will remain saved on the memory card until it is deleted manually, or the SD card is formatted.

• Recording options and settings description- Once you are in the recording mode,  Click the Menu button to bring to the first page of the recording settings: 

• Another Click on the Menu button will bring the second list of the settings:

• Use the UP and DOWN buttons(on the left side of Dash Cam) to navigate these settings, and OK button(on the right side of the Dash Cam) to enter each setting or confirm changes

Resolution- 1296P/ 1080FHD/ 720P/ VGA 

• Recommended setting (may vary on your personal needs and preferences): 1296FHD

Cyclic record-(Loop recording) Off/ 1Minute/ 3Minutes/ 5Minutes 

• The video recordings will be saved in time segments 1- 3 -5 Minutes depending on your selection within this feature. Loop recording on a dashcam allows for continuous recording even if the SD memory card reaches full capacity. This means older files are overwritten once the SD card reaches its file size limit. In the event of an incident, any files that have been protected by activation of the G- sensor, or by manually pressing the lock button will not be overwritten and will stay on the SD card. Therefore, important clips that can be used for insurance purposes or sent to the Police will stay locked on the card and will not be deleted. This also means that, at some point, your SD card will be full of protected recordings, and the SD Card would need to be formatted in order to make free space. 

High Dynamic Range- Off/On

• It improves contrast in an image while maintaining clarity. HDR can be particularly important in a Dash Cam in helping to produce vibrant and clearer imagery, ultimately resulting in enhanced footage. When driving at night time and in low light levels, HDR can significantly improve image clarity. It will record multiple exposure levels for each frame and conduct tone mapping to ensure the optimum footage is recorded.

Exposure- +3/ +2/ +1/ 0/ -1/ -2/ -3

• Increasing exposure makes videos and images look lighter or darker. If your video is too dark, the selection of a positive number is recommended. If your video is too bright, select negative numbers

Motion Detection- Off/On

• Motion detection is a memory-saving feature that only records footage where motion is taking place. It’s supported only when the car is in the ignition. 

Recording- Off/On

• The device has a built-in microphone for recording audio in the cabin. When On is selected, the audio recording will be enabled, and if it is set to Off, an audio recording will be disabled

Date Stamp- Off/On

• Select ON if you want the date on the recordings

Gravity sensing (G-sensor)- Off/ Low/ Medium/ High 

• The Dash Cam includes a built-in G-Sensor which allows the device to determine when the car has been in a collision. If it detects a collision, it automatically locks the recording being made at the time of the accident. High selection will make the system more sensitive, and low setting ensures the system will react only to greater shocks

Parking guard- Off/On

• This feature is available only when the car is in the ignition. The parking guard uses the Motion Sensor and G-Sensor to optimize recording functionality while your vehicle is parked. The idea is that when you are parked, the dashcam will be “sleeping” but it will monitor the video image for motion and it will also monitor the G-sensor. If it detects motion or if it detects an impact then the unit will wake up and start recording

Car Number- Off/On

• Select ON if you want the car number on the recordings

LCD Brightness- Off/ 30 Seconds/ 1Minute/ 2Minutes 

• This option allows you to set the duration after which the device’s display will go dark, and the camera will still keep recording. The screen will turn dark after 30 Seconds/ 1Minute/ 2Minutes, based on the selected option. It is highly recommended to use this feature in order to avoid distractions while driving

Auto Power Off- Off/ 3 Minutes/ 5 Minutes/ 10 Minutes

• This feature enables the Dashcam to shut down by itself after the selected interval of time (3 Minutes/ 5 Minutes/ 10 Minutes) 

Frequency- 50Hz/60Hz

• Choose 60Hz for the USA

Beep Sound- Off/On

• Turns the beep sound On or Off when pressing camera buttons

Language- Japanese/ German/ Thai/ English/ Vietnamese/ Russian /Chinese

Date/Time- Supported

Format- Cancel/ OK 

Default Settings- Cancel/ OK 

• Returns camera settings to default values

Version- May vary depending on the batch 

PHOTOGRAPH 

When you are in the Recording mode (which is a default setting when the Dash Cam is turned on). Short press M button to enter Photograph mode. Click the “OK” button to take a picture. 

-Photograph options and settings description

Capture mode- here you can set the delay between pushing the button for taking pictures and the point at which the photo is recorded 

• Single shot 

• 2s Delay

• 5s Delay 

• 5s Delay  

Resolution- Photograph resolution formats are: 

VGA / 1.3 MP/ 2MP/ 3MP

Continuous shooting- ON/OFF 

Exposure- +3/ +2/ +1/ 0/ -1/ -2/ -3

Date Stamp- Off/On

PLAYBACK

Once you’ve entered recording mode, one pressing of the “M” button will bring you to Photograph mode, and another pressing of the “M” button will bring you to the Playback mode. 

Use UP and DOWN buttons to go through your files, and use the “OK” button to playback the video. 

-Playback options and settings description

Delete- Delete Current? / Delete All?

Protection- Lock One/ Unlock One/ Lock All/ Unlock All 

Slideshow- 2 seconds/ 5 seconds/ 8 seconds 

BATTERY

Dashcams take their power from the cigarette lighter in your car. The device contains a battery whose purpose is to backup and save the data only. When your vehicle ignition is turned on, power is delivered to the cigarette lighter and the car camera will be activated.

 Battery indication image：

The red indicator light will light up when charging. The entire charging time is about 180 minutes. The red indicator light automatically turns off when charging has been completed

***Important note: The internal battery can last for only about 10 minutes or less and its purpose is back up and save the data only

Supports: 

1. Mini-USB charging

2. Vehicle power charging

WARNING

• Do not disassemble the camera yourself to avoid damaging the internal components.

• Please do not place the camera under strong sunlight or high temperature. This may damage the shell internal parts.

• When inserting or removing the memory card, please keep the camera in a power-off state. If not, the card and the data may get damaged.

• The machine may be heated after working for a period of time, which is normal.

• Please use a lens cleaner or professional tools to clean the lens.

PRODUCT SPECIFICATIONS

Video Doorbell User Manual

About the product:

• 1. PIR Motion Sensor    

• 2. Led light (Optional)   

• 3. Light Sensor

• 4. 166°HD Camera 

• 5. Microphone

• 6. Ring-a-bell button  

• 7. LED indicator 

• 8. Speaker         

• 9. Reset Button 

• 10. AC input 

• 11. Battery compartment 

• 12. Memory card slot 

• 13. USB port 

What’s in the box?

Doorbell	Mounting bracket	Mounting Screws	4.  Smaller Security Screws
5.  Anchors	6.  Batteries	7. Chime	8. User manual

***The device needs a Micro USB cable to recharge the batteries, not included in the package

How to start? 

Important notes:

*After the battery insulation film has been removed, the device will be ready for pairing with your smartphone.

*The device is powered by rechargeable lithium batteries. With fully charged, the battery life is approx six months of standby mode.

 * Motion detection can sometimes false alerts because of large heat sources such as cars, the rising or setting sun or reflections off a shiny object. Please install the video doorbell in a place to avoid the sun.

* Not fully waterproof, please install it in the area without rain.

 *The Wireless Video Doorbell supports WIFI 2.4GHz, DOES NOT support WIFI 5GHz.

  *In a crowded environment, it is recommended to close or set the device to low sensitivity to reduce device arousal and call times to extend battery life.

Setup Device

1. Step one: Download the App! Open the App Store (for iOS) or the Google Play Store (for Android) on your mobile services. Search for „XSH cam“ or scan the following QR Code to download and install it to your device.

2. Step two: Select Wi-Fi - Please enter your Wi-Fi name and Wi-Fi Password- Tap Next. 

3. Search Device - Please power on the device, and you will be able to hear a voice prompt „The camera is now ready to begin pairing“. 

 If you didn’t hear the voice prompt, press and hold the reset button for 5 seconds. Release after the LED indicator turned off, and the device will restart to configure automatically.

4. Step four: Tap Add device 

After a successful connection, you will be prompted to create a name and password for your camera. The password must be at least 8 characters and include an uppercase letter, a lower-case letter, and a number, the name is completely at your choice. 

Setup completed! The APP will be entered into the device list interface automatically. Congratulations! The device is ready to use.

Settings

Once you have everything installed, and you tap on the XSH cam app, you will enter the Device section. 

In the Device list section, please click the settings icon which is at the top right corner to enter the device settings.

Accept call 

Share QR code 

Cloud storage 

Remove

Accept call- You will have three different selections within this feature: 

Silence- Tap this button if you do not wish to receive the notification on your phone that someone rang the bell

Notification- Tap this button if you wish to receive the notification on your phone that someone rang the bell 

Call in- Each time someone rings the bell, your phone will ring the same way as if someone is calling you. If you decide to “take the call”, you will be taken to live view and you will be able to see who’s at your door, like in an image below 

1. Tap to take a photo of the event 

2. Live 2-way speech; Tap the microphone if you wish to have verbal correspondence with the visitor 

3. Tap to make the video recording of the event 

Share QR code 

Send the QR code to share the device with your friends and family or someone that you want to share.

Cloud Storage 

Cloud storage Description: When the Device is in the sleep state when the PIR is triggered or the doorbell button was pressed, the device will automatically upload 10 seconds of video to the cloud. Each device can record 20 events per day, and provide a week of loop recording space and Traffic for users.

Tap the trash bin icon if you wish to delete the recording. Tap the calendar icon in the upper right corner and select the date to see all the cloud videos for the selected date

Remove

The mobile device will not receive the notifications after you delete the camera. But the camera still works and the other connected mobile devices are still able to receive the notifications.

In the Device list section, please click the camera icon which is at the top left corner to enter the live view. 

At the bottom of the live view, you will be able to see the Menu which displays: 

Album, Cloud storage, Cruise, Voice, Settings. 

Album- Tap this icon to see all the snapshots or video recordings of the events you have saved 

Cloud storage- Tap this icon to see the events that the device has captured 

Cruise- the camera will zoom in and scroll left to right according to pre-set automatic patrol paths

Voice- Use this icon to enable or disable voice recording 

Settings- Tap this icon to enter device settings 

Device settings: 

SD card: Here you can select the type of storage space you want to use or the status of the available space. Within this feature, you will also be able to Format the SD card.

Orientation: Selections are Normal, Rotate, Mirror, and Mirror-Rotate

Environment: Selections are Normal, Backlight compensation, Night IR, Night light compensation, Dynamic 

PIR detection: Selections are Disabled, Low, Medium, High. Disabled- Close the PIR function

• Low- The device will be able to wake up after the device detects humans for 7 seconds. The device starts to take videos and notifies the mobile device at the same time
• Medium- The device will be able to wake up after the device detects humans for 5 seconds. The device starts to take videos and notifies the mobile device at the same time
• High- The device will be able to wake up after the device detects humans for 7 seconds. The device starts to take videos and notifies the mobile device at the same time

***NOTE: In a crowded environment, it is recommended to close or set the device to low sensitivity to reduce device arousal and notification times to extend battery life.

Dormancy time: Selections are 15s, 30s, 60s, Not dormant. The dormancy time refers to: after the PIR has not detected the object, the doorbell will continue to work for a while. After this time, the doorbell will go to sleep and wait for the next wake-up. The “not dormant” state means that the camera will remain working.

Power frequency: Selections are 50Hz, 60Hz

LED lamp: Selections are Enabled/Disabled 

Basic Settings: 

Device name and password 

Share QR code 

Basic Info 

Name: Device name 

ID: LPHWAOLLQ3ULDRECNETQ

Model: M12-2O0B1054

Firmware version 141.0.5.58

Vendor: XSH cam

Check for update

Specifications

Wireless Chime (Optional)

Connect the video doorbell to the doorbell chime, and get an instant alert in your home when someone rings the doorbell. Hear the doorbell chime when you are at home, without checking your video doorbell app! The chime plugs into any wall outlet, you can place it anywhere in the home.

NOTICE: 

The video doorbell is only compatible with our wireless chime, and not compatible with traditional doorbell chimes. The wireless chime is optional. If it is not installed, doorbell notifications will still go directly to the XSHcam app.

The Basics 

Getting Started 

Set up your chime with the video doorbell 

STEP 1 

Before the setup process, be sure your video doorbell has connected to your phone and plug in your chime.

 STEP 2  

Press the forward or back button to cycle through 55 different tunes and select a tune.

STEP 3

Press and hold the volume button for 5 seconds until the chime emits a Ding sound and the blue indicator flashes.

 STEP 4

Press the doorbell button, the chime emits a Ding sound.

STEP 5

Press the doorbell button again, the chime will automatically play the tune you selected.

XG-20 

BLUETOOTH 5.0

True Split Wireless Bluetooth Headset 

USER MANUAL

DUAL EARBUDS MODE- AUTOMATIC PAIRING

(This mode is suitable for first-time use)

First step: Remove the charging insulation sticker from the back of the dual headphones and put them back into the charging case, activating both sides of the earbuds. 

NOTE: If the earbuds are not charging after they are placed into the charging case, please kindly use a USB charging cable as it might happen that the charging case is empty and the battery of the charging case needs to be recharged as well. 

Second step: After recharging, take the two earbuds out of the charging case (both of them), they will automatically turn on, and led light will flash blue. 

You will hear the voice prompt: “Power ON Pairing”, please expect the pairing process to last 7-10 seconds. After pairing is completed, you will hear the voice prompt: “Pairing Success”. 

Third step: The LED of the left earbud will flash red and blue alternately until it enters the pairing mode. Please turn on the Bluetooth function on your phone and select XG-5.0 on your list. You will hear the voice prompt “Connected” once they are paired. Start enjoying music or making phone calls. 

***Note: After successful pairing, every time you take earbuds out of the charging case, if the Bluetooth is turned ON on your mobile phone, they will connect to your mobile phone automatically. 

DUAL EARBUDS MODE- MANUAL PAIRING

(This mode is suitable if automatic pairing fails)

First step: Press the earbud button for about three seconds until LED starts flashing blue and you hear the voice prompt ”Power ON Pairing”, please expect the pairing process to last 7-10 seconds. After pairing is completed, you will hear the voice prompt: “Pairing Success”. 

Second step: The LED of the left earbud will flash red and blue alternately until it enters the pairing mode. Please turn on the Bluetooth function on your phone and select XG-5.0 on your list. You will hear the voice prompt “Connected” once they are paired. Start enjoying music or making phone calls. 

Note: After successful pairing, every time you take earbuds out of the charging case, if the Bluetooth is turned ON on your mobile phone, they will connect to your mobile phone automatically. 

FUNCTIONS AND OPERATION 

TURN ON/OFF- Long press any side of the earbud (for about 4 sec) to turn it ON or OFF

PLAY/PAUSE- Light touch any side of the earbuds to Play/Pause

ANSWER/ REJECT PHONE CALL- Press Main (Left headset) during the call if you want to pick up the call, or hang up. Long press the main (Left headset) for about one sec if you wish to reject the call. 

PREVIOUS SONG/NEXT SONG

In the music play state, double click the left earbud to switch to the previous song. 

In the music play state, double click the right earbud to switch to the next song. 

VOLUME UP/ VOLUME DOWN- In the music play state, triple-click the left earbud to decrease the volume, and triple-click the right earbud to increase the volume. 

WAKE UP SMART VOICE ASSISTANT (Such as Siri)- When the earbuds are under the using state or in standby mode, long-press the main (left earbud) for about 1 sec to wake up the voice assistant

TURN OFF SMART VOICE ASSISTANT (Such as Siri)- When using a voice assistant,  long-press the main (left earbud) for about 1 sec to turn off Siri 

***Note: In the dual earbud mode, when you are using earbuds for the purposes of phone call/ talking/ voice assistant, only the microphone on the Left earbud will be active, the right microphone will not be active. As soon as the phone call is finished, the earbuds will go back to dual earbuds mode automatically. 

SINGLE EARBUDS MODE- LEFT EARBUD

First step: Take the Left earbud out of the charging case, it will enter into the pairing state automatically. 

Second step: Please turn on the Bluetooth function on your phone and select XG-5.0 on your list. At the same time, the right earbud should be placed into the charging case to get charged and it should be turned off.

SINGLE EARBUDS MODE- RIGHT EARBUD

First step: Take the Right earbud out of the charging case, and long-press for about three seconds. It will enter into the pairing state automatically. 

Second step: Please turn on the Bluetooth function on your phone and select XG-5.0 on your list. At the same time, the left earbud should be placed into the charging case to get charged and it should be turned off.

EARBUDS CHARGING PROCESS

When both earbuds are placed into the charging case, the light of the LED display screen which shows the battery amount will flash green. If the green light indicator is going up and down (1-4 and 4-1), it indicates the earphones are charging. When the four green lights are shown on the LED display screen, it means that the earphones are fully charged. The green light on the LED display screen and earbuds will turn off automatically. 

CASE CHARGING PROCESS

Please use the power cord supplied to charge the charging case. 

While charging, the LED display will show the power lever, for example, 88 means the power is 88% charged. When charging is completed, the light indicator will go off. 

BLUETOOTH SIGNAL 

Do not cover the earbuds by ear or hand as it will interrupt the Bluetooth signal. 

Please use these earbuds within their working range (10 meters) and avoid obstacles in between connected devices 

PRODUCT SPECIFICATIONS

Model name: XG-20

Version: 5.0 + EDR 

Charging voltage: DC 5V 

Battery voltage: 3.7V 

Charging time: 0.6h 

Talking time: 3h

Music time: 3.5h

Work range: 10m

Battery capacity: 50mAH

Standby time: 120h

Case input current: 5V/ 1000mA

Earbud input current: 5V/ 100mA

Battery capacity: 1800 mAH

Charging time for earbuds when charged from a fully charged case: 13 times

IMPORTANT NOTICE

For the first-time use, please fully charge this product 

Please do not disassemble or remodel the product, it will cause a short circuit which might cause fire or completely damage the product 

Don’t use earbuds at temperatures below 0 °C or above 45 °C

Avoid using the device near children, animals or people with photo sensitivity due to strong flashing light 

Don’t use earbuds under thunderstorms, it may cause device malfunction and increase the risk of electric shock 

Don’t clean the product with oil or other volatile liquids 

Do not let the device get wet with liquids 

Do not use the device for a long time as it may cause hearing damage, arrange the use time reasonably 

VesperSecurity Wireless Outdoor Security Camera

VesperSecurity Wireless Outdoor Security Camera

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dual Dash Camera 4" LCD Display 

User Manual 

 Product Structure

1. Back clip fixation hook         9. Memory card slot

2. USB port (mini USB)           10. Reset button 

3. Rear camera port                 11. Lens 

4. Mode selection key

5. Up key 

6. OK/Power key

7. Down key 

8. MENU key 

Installation guide

***Before the installation, please insert the Memory Card in the TF slot and format the memory card prior to use. 

****IMPORTANT NOTE-  When inserting, gently slide the card into the memory card slot until it clicks into place. Electrical contacts of the memory card should be facing the camera lens side of the camera. When removing, push down gently on the microSD card with the top of your finger or the blunt tip of a pen. It will pop up and can then be removed. You are suggested to use a class 10, 128GB max micro SDHC card.*

Install the front camera attached to the windshield using the suction cup and connect the power adapter to the 12V cigarette lighter socket and route the cable in the interior/hide the excess cable into the interior panel and gaps to obtain a visual aesthetic. 

It is recommended to connect the rearview camera above the license plate, this might require drilling 2 holes and attaching them with the screws from the kit. 

Connect the RED cable to the positive lead of the reverse light wires (Cord that connects your car's tail lights to the dashboard) Important Note: This might require a little knowledge of car electronics, in case you are not sure how to properly set it up, it is highly recommended to seek for professional help, such as a car electrician. 

Route the rear cam cable to the front of the car and connect it to the main unit. 

After the installation is completed, please turn the unit ON by pressing the power button and starting the engine.

Key Function Description

1. Back clip fixation hook (Fix video recording instrument)

2. USB port (mini USB)   

3. Rear camera port                

4. Mode selection key (Press this key to switch between camera/photo/playback)

5. Up key 

6. OK/Power key (To turn the device On or OFF, short press this button. Short press ON/OFF: Video and photos confirmation buttons, Video mode: press this button to start the video, press this button again to stop the video: Press this button to shoot photos).

7. Down key 

8. MENU key 

9. Memory card slot 

10. Reset button

11. Lens 

The MAIN MENU will give you the following selections: 

1. RECORD      2. PHOTO MODE      3. FILES     4. SETTINGS 

SETTINGS

Screen saver:  Close, 30 Seconds, 60 Seconds, 120 Seconds (this feature shuts down the screen but the Dashcam will keep recording, recommended to use to avoid getting distracted during the drive)

AUTO-OFF: Close, 3 Minutes, 5 Minutes, 10 minutes (The car dash camera will start recording immediately after igniting, shut down and save the video when you shut off the engine.)

Light frequency: 50/60 Hz

Key sound: Close/Open 

Language: Select the language of your preference 

LED:  Close/Open 

Date/Time: please use these buttons to adjust the date and time 

License plate: You can enter your license plate and it will show on the footage 

Headlights: Close/Open 

Format:Close/Open 

Default settings:

Version number

VIDEO RECORDING MODE SETTINGS

In the video recording mode, please tap the Settings icon to open the video settings. You will find the following features: 

•  

  Resolution:  tap this button to select your preferable video resolution (default 1080PHD)

•  

  Dual:  Close/Open (use this button to select dual mode- both front and rear)

•  

  Cycle: Close, 1 Min, 3 Mins, 5 Mins (use this button to adjust the loop recording of your device. The video recordings will be saved in time segments of 1- 3 -5 Minutes depending on your selection within this feature. Loop recording on a dashcam allows for continuous recording even if the SD memory card reaches full capacity. This means older files are overwritten once the SD card reaches its file size limit. In the event of an incident, any files that have been protected by activation of the G- sensor, or by manually pressing the lock button will not be overwritten and will stay on the SD card. Therefore, important clips that can be used for insurance purposes or sent to the Police will stay locked on the card and will not be deleted. This also means that, at some point, your SD card will be full of protected recordings, and the SD Card would need to be formatted in order to make free space.)

•  

  Interval: Close,  100ms, 200ms, 500ms. 

•  

  HDR: (It improves contrast in an image while maintaining clarity. HDR can be particularly important in a Dash Cam in helping to produce vibrant and clearer imagery, ultimately resulting in enhanced footage. When driving at night time and in low light levels, HDR can significantly improve image clarity. It will record multiple exposure levels for each frame and conduct tone mapping to ensure the optimum footage is recorded.)

•  

  Exposure: (Increasing exposure makes videos and images look lighter or darker. If your video is too dark, the selection of a positive number is recommended. If your video is too bright, select negative numbers)

•  

  Motion:  Close/Open (Motion detection is a memory-saving feature that only records footage where motion is taking place. It’s supported only when the car is in the ignition.)

•  

  Watermark: Use this feature to add a watermark to your recordings 

•  

  Gravity: Close/ Low/Medium/High (The Dash Cam includes a built-in G-Sensor which allows the device to determine when the car has been in a collision. If it detects a collision, it automatically locks the recording being made at the time of the accident. High selection will make the system more sensitive, and a low setting ensures the system will react only to greater shocks)

•  

  Sound: Close/Open (Use this button to enable or disable audio recording on your footage)

•  

  Guard- Parking mode (In order to record when you're not driving your dashcam will need power from a hardwire installation)

•  

  License (adding your car’s license plate numbers, which will also be visible in your recordings )

PHOTO MODE SETTINGS

In the photo mode, please tap the Settings icon to open the photo settings. You will find the following features: 

•  

  Resolution:  tap this button to select your preferable video resolution (VGA, 1M, 2M, 3M, 5M, 8M, 10M)

•  

  Delay: Shot, Delay 2s, Delay 5s, Delay 10s

•  

  Continuous: Close/Open

•  

  Quality: Good, Standard, Economy 

•  

  Sharpness: Strong, Standard, Soft

•  

  WB: Auto, Sunlight, Overcast, Tungsten, Florescent (white balance)

•  

  Color: Normal, B/W, Nostalgic 

•  

  ISO: Auto, 100, 200, 400 (picture brightness)

•  

  Exposure: -3, -2, -1, 0, +1, +2, +3

•  

  Anti- Shake: Close/Open (stability at the moment you take a picture)

•  

  Preview: Close, 2s, 5s

•  

  Watermark

Dual-mode and rear camera installation

 Once the rear camera has been connected, tap this icon to switch between front view, rear view, or dual view. 

*Using a Phillips head screwdriver, remove each of the screws holding your rear license plate in place. Then, pull the plate off and set it aside. Make sure you don't lose the screws, right above the license plate, place the rear camera, and using a marker, mark the two holes through the rear camera stand. Make sure the camera is aligned straight.

*Pop open your trunk and look for a solid interior panel covering the opposite side of your license plate mounting area. Removing this panel will expose the car’s rear wiring chambers.

*Please connect the RED cable to the positive lead of the reverse light wires (The cord that connects your car's tail lights to the dashboard). Reverse light wires are the cords that connect your car’s tail lights to the dashboard. They hook directly into your vehicle’s tail lights and are normally located in the hatch or trunk of your car.

*Using a wire stripper or pliers, peel back the rubber covering the wires. Then, use a screwdriver or other thin tool to poke a hole through the middle of each exposed wire, separating the individual wire strands.  (For safety, make sure you do this while the car is turned off.)

*Attach 1 of your bare wire cables to the camera cord’s power connector. Then, poke your bare wires through the center of the exposed reverse light wires and twist them together. For safety, make sure you wrap the combined wires in electrical tape. 

*important* (Make sure you poke your positive (usually red) bare wire through the positive reverse light wire and the negative (usually black) bare wire through the negative reverse light wire.)

*Connect your RCA cable to the camera cord’s video connector if necessary. Then, run it through your vehicle to the area by the fuse box. Depending on your vehicle model, you’ll usually be able to do this by peeling back the automobile’s headliner or side panels and pulling your cable through the exposure chamber.

You have two different installation methods the position of the rear camera depends mostly on the view angle you prefer the most: 

Hardwiring Instructions 

INTRODUCTION

A hardwire kit is a device used to help you directly connect your dashcam to your vehicle’s fuse box. By hardwiring your dashcam, you’ll be able to run and operate your dashcam 24/7, even when your vehicle is turned off.

The installation process should take around 20 minutes and will require several tools to ensure a safe installation. Before you begin, please get familiar with the Fuse Box of our vehicle. Understanding the role and how the fuse box works will be crucial to the installation process.

Hardwiring your dashcam is an advanced installation method that requires technical know-how. We highly recommend reading through this guide in its entirety before beginning.

***NOTE:  Improper installation and handling may cause serious damage to your vehicle and Dashcam. 

• The seller is not liable for any mishandling or damages that occur due to improper installation or misuse of the device. 

• Please check the health of your vehicle’s battery before installing your hardwire kit and dashcam. If your car battery is in poor health, we recommend replacing your battery.

REQUIRED TOOLS

For hardwiring your Dashcam you will need:

1. Hardwiring kit 

2. Add-a-Fuse taps and extra fuses ( sizes: ATO (regular), mini fuse, low profile mini fuse, Micro 2 fuse. Fuse sizes vary depending on your vehicle design and model, make sure to check your fuse box to see what type of fuse your vehicle requires)

3. A multimeter or circuit tester

4. Pliers, fuse puller, wire crimper, or a clamp

PROCEDURE

• Locate your fuse box and remove the pannel- The location of your car fuse box will differ from car to car. In most cases, your vehicle’s fuse box can be located inside the engine bay or inside your trunk. Refer to your user manual for the exact location of your battery.

• Decide which fuse to use- We suggest using fuse slots rated between 10A-30A. Avoid fuses related to safety features, such as airbags, horns, stability control programs, etc. Fuses that control certain elements such as the radio, cigarette lighter, garage door opener, sunroof, etc. are usually safe to use. 

Different cars use different fuse types, select the fuse tap that matches the fuse type you have in your car ( ATO (regular), mini fuse, low profile mini fuse, Micro 2 fuse)

• Hardwire cable includes 2 wires (red wire, and ground-black wire) that will need to be connected to the fuse box. The constant fuse slots will always have power and ACC fuse slots will only have power when the ignition is on. 

• The black wire is ground

• Check which fuse type your car uses and crimp the red wire of the cable to the appropriate size fuse tap

• Choose the most suitable fuse. Open your fuse box and use the multimeter to find a constant 12-volt fuse. 

• Probe the fuse you have selected (it can be a lamp or some other minor car fuse) to see if it has constant power (the car must be off, with no ignition, when the car is off, the multimeter should show voltage when you probe it with Multimeter). Using a fuse puller or a pair of pliers, gently remove the fuse you have selected. 

• The fuse tap has two fuse slots: the upper is for powering the Dashcam, use the new fuse (make sure it has lower or equal amperage than the original fuse) and put it in the upper slot, the bottom slot is for the fuse you have taken out of your car, please put it in there. 

• Plug the fuse tap into the fuse box. 

IMPORTANT STEP: Make sure you put the fuse tap in the correct orientation. Each fuse slot has a positive and a negative terminal depending on your vehicle’s model. This means that the power is coming into your fuse slot from one side and exiting from the other. Use your circuit tester or multimeter to test each terminal of the constant fuse slot for power. 

The terminal with the power is positive and the terminal with no power is negative.

After testing the terminals of the constant fuse slot, insert the fuse tap (Add-a-Fuse)in such a way that the terminal that is furthest away from the wire goes into the positive terminal of the fuse slot. 

• Ground your wire- The metal ground will need to be attached to a metal bolt or screw within the vehicle chassis. This is achieved by loosening the bolt/screw, sliding the connector underneath the bolt, and tightening again.

• Hide a cable- Lead and tuck the cable up to the headliner and your Dashcam

• Plug the cable into the Dashcam and turn it on 

Note: 

• Make sure your Parking more is turned ON (check settings) so that it can turn on every time the vehicle detects impact 

Troubleshooting

If the product presents problems, please refer to the solutions below: 

-Can’t take photos, Camera: 

Check if the TF card has enough space, or if too many saved files. 

- Video automatically stops: 

Because of the huge high-definition video data, please use a high-speed TF card and SDHC compatible, high-speed TF card will be a class 10 Micro SD card. 

- Picture or video replay, “File Error” Prompt: 

An error occurred while the TF card storage of data, according to the files are not complete, please use the “format” camera function reformatting the TF card. 

-Shoots a foggy image:  

Please check if the camera lens is dirty, or it has fingerprints, use a piece of cloth or a wipe to clean the lens. 

-Dark Image:

In a contrasting scene, the device automatically adjusts the EV exposure and image brightness. 

You can adjust the EV value on the device setting menu. In the indoor light, the color might not be perfect. 

Please check the device's “White Balance” function is set to automatic. 

-Horizontal Stripes - Interference in the image:

This is due to the error of the “light source frequency”, please adjust according to the local power supply frequency, set to “50 Hz” Or “60Hz”. 

-Crash: 

Please press the reset button down.